The L-series
LR7/90
- RBN401 pro-ribbon HF driver with exceptional intelligibility and “throw”
- Patented constant horizontal dispersion up to beyond 20 kHz
- Left/Right system from single cabinet with Androgyn™ flying system
- SIS™ pre-wired for very high damping and further reduced distortion (with ALC)
- Ultra-compact enclosure provides versatile array deployment
- All Neodymium drivers for excellent performance-to-weight ratio
Product description
The LR7 is a passive 2-way “micro-sized” line-array sound system, to be used as vertical array, either in stacked or flown configuration, for both portable and permanent installations.
Loaded with the RBN401 pro-ribbon driver on a “Morpher” lens (up to 94% frontal radiation), the system offers a very high throw-efficiency and projection control up to directly under the array, due to the pro-ribbon’s all-natural cylindrical (Isophasic) wavefront.
Its transient response and unusual high peak power handling (800W @ 200ms) cater for a perfect intelligibility from the lowest to the highest SPL with a 1:15 dynamic range, while offering maximum “gain-before-feedback”.
The system features a consistent, patented horizontal dispersion with seamless coverage, available in 90° and 120° configuration.
The micro-compact size, combined with the weight-saving all-Neodymium drivers, makes the system very easy to handle in a wide variety of configurations; As stacked or flown line-array, or with 3 or 5 modules as “speaker-on-a-stick”; In applications where extended bass response is
required, the LR7 can be combined with the LR7B line-array bass module and/or a stacked subwoofer system.
The Androgyn™ flying hardware enables an acoustically-symmetric left / right system, with the asymmetric LR7 module.
The LR7 is driven by the Sentinel amplified loudspeaker controller, optimising the system’s response by LR7-specific drive processing and feedback for each array configuration, including presets for phase-matched low-frequency extensions.
The Signal Integrity Sensing™ pre-wiring ensures dynamic cable/connector compensation between the LR7 and ALC; This offers a 1:1, undistorted natural sound reproduction, regardless of cable length and amplifier impedance load (system damping factor 10.000).
Typical (short to medium throw) applications for the LR7 include as compact main system for performing arts theatre, A/V or corporate events where with exceptional sound reproduction is required, with minimal sightline obstruction.
LR7/120
Product description
The LR7 is a passive 2-way “micro-sized” line-array sound system, to be used as vertical array, either in stacked or flown configuration, for both portable and permanent installations.
Loaded with the RBN401 pro-ribbon driver on a “Morpher” lens (up to 94% frontal radiation), the system offers a very high throw-efficiency and projection control up to directly under the array, due to the pro-ribbon’s all-natural cylindrical (Isophasic) wavefront.
Its transient response and unusual high peak power handling (800W @ 200ms) cater for a perfect intelligibility from the lowest to the highest SPL with a 1:15 dynamic range, while offering maximum “gain-before-feedback”.
The system features a consistent, patented horizontal dispersion with seamless coverage, available in 90° and 120° configuration.
The micro-compact size, combined with the weight-saving all-Neodymium drivers, makes the system very easy to handle in a wide variety of configurations; As stacked or flown line-array, or with 3 or 5 modules as “speaker-on-a-stick”; In applications where extended bass response is
required, the LR7 can be combined with the LR7B line-array bass module and/or a stacked subwoofer system.
The Androgyn™ flying hardware enables an acoustically-symmetric left / right system, with the asymmetric LR7 module.
The LR7 is driven by the Sentinel amplified loudspeaker controller, optimising the system’s response by LR7-specific drive processing and feedback for each array configuration, including presets for phase-matched low-frequency extensions.
The Signal Integrity Sensing™ pre-wiring ensures dynamic cable/connector compensation between the LR7 and ALC; This offers a 1:1, undistorted natural sound reproduction, regardless of cable length and amplifier impedance load (system damping factor 10.000).
Typical (short to medium throw) applications for the LR7 include as compact main system for performing arts theatre, A/V or corporate events where with exceptional sound reproduction is required, with minimal sightline obstruction.
LR7B
Product description
The LR7Bass is a double-tuned band-pass bass system, matching the LR7 line-array in both permanent and portable applications. Featuring a single 12” long excursion woofer with Neodymium magnet structure, the LR7B delivers high quality, high output bass response from an ultra-compact and weight efficient package. The concentric bandpass configuration offers LR7-tuned bass response in full-space (flown) and increased efficiency in half-space (stacked) applications
The extended frequency response enables the LR7B to be used as mid-bass reinforcement, full-range bass extension or subwoofer.
The integrated flying system, combines light weight with high WorkingLoadLimit and makes for a quick system set-up in combination with the LR7 line-array module.
The SIS pre-wiring ensures complete cable/connector compensation between the LR7Bass and ALC;
The LR7Bass is to be used in combination with an ALC amplified loudspeaker controller, then delivering maximum sound quality and output power with dedicated and inaudible (power and excursion!) protection.
LR14/90
Product description
The LR14 is a passive 2-way line-source loudspeaker system. It is a true line-array system, to be used as vertical array, either in stacked or flown configuration, for both portable and permanent installations. Loaded with the RBN401 pro-ribbon driver on a “Morpher” lens (up to 94% frontal radiation!), the system features 90° horizontal dispersion with seamless coverage, due to the pro-ribbon’s all-natural cylindrical (Isophasic) wavefront. Its transient response and unusual high peak power handling (800W/200mS) caters for an amazing intelligibility and throw, while offering maximum “gainbefore- feedback” up to directly under the array.
The ultra-compact size, combined with the weight-saving all Neodymium drivers, makes the system very easy to handle.
The “Morpher” is mounted in the “ALrad™” waveguide, which utilizes the stiffness and heat transfer capabilities of aluminium. Mounted on the RBN, the ALrad™ extens the cooling surface for even further reducing power-compression for increased SPL over time.
The SignalIntegritySensing™ pre-wiring ensures complete cable/connector compensation between the LR14 and ALC. Typical (short to medium throw) applications for the LR14 include as compact main system for theatre and A/V applications. It is available in 90° and 120° configuration.
The system includes dedicated filtering, but system equalizing is done remotely (electronically) fully utilizing the individual speaker components’ power capacity. This results in increased headroom SPL.
In applications where extended bass response is required, the LR14 can be combined with a pressure-bass (LR14B) or deep-sub system (B-series), or both.
For full system performance, the LR14 needs to be driven by an ALC amplified loudspeaker controller. Driven by the ALC, the LR14 delivers maximum sound quality with inaudible (power and excursion) protection.
LR14/120
Product description
The LR14 is a passive 2-way line-source loudspeaker system. It is a true line-array system, to be used as vertical array, either in stacked or flown configuration, for both portable and permanent installations. Loaded with the RBN401 pro-ribbon driver on a “Morpher” lens (up to 94% frontal radiation!), the system features 120° horizontal dispersion with seamless coverage, due to the pro-ribbon’s all-natural cylindrical (Isophasic) wavefront. Its transient response and unusual high peak power handling (800W/200mS) caters for an amazing intelligibility and throw, while offering maximum “gainbefore- feedback” up to directly under the array.
The ultra-compact size, combined with the weight-saving all Neodymium drivers, makes the system very easy to handle.
The “Morpher” is mounted in the “ALrad™” waveguide, which utilizes the stiffness and heat transfer capabilities of aluminium. Mounted on the RBN, the ALrad™ extens the cooling surface for even further reducing power-compression for increased SPL over time.
The SignalIntegritySensing™ pre-wiring ensures complete cable/connector compensation between the LR14 and ALC. Typical (short to medium throw) applications for the LR14 include as compact main system for theatre and A/V applications. It is available in 90° and 120° configuration.
The system includes dedicated filtering, but system equalizing is done remotely (electronically) fully utilizing the individual speaker components’ power capacity. This results in increased headroom SPL.
In applications where extended bass response is required, the LR14 can be combined with a pressure-bass (LR14B) or deep-sub system (B-series), or both.
For full system performance, the LR14 needs to be driven by an ALC amplified loudspeaker controller. Driven by the ALC, the LR14 delivers maximum sound quality with inaudible (power and excursion) protection.
Product description
The LR14 is a passive 2-way line-source loudspeaker system. It is a true line-array system, to be used as vertical array, either in stacked or flown configuration, for both portable and permanent installations. Loaded with the RBN401 pro-ribbon driver on a “Morpher” lens (up to 94% frontal radiation!), the system features 120° horizontal dispersion with seamless coverage, due to the pro-ribbon’s all-natural cylindrical (Isophasic) wavefront. Its transient response and unusual high peak power handling (800W/200mS) caters for an amazing intelligibility and throw, while offering maximum “gainbefore- feedback” up to directly under the array.
The ultra-compact size, combined with the weight-saving all Neodymium drivers, makes the system very easy to handle.
The “Morpher” is mounted in the “ALrad™” waveguide, which utilizes the stiffness and heat transfer capabilities of aluminium. Mounted on the RBN, the ALrad™ extens the cooling surface for even further reducing power-compression for increased SPL over time.
The SignalIntegritySensing™ pre-wiring ensures complete cable/connector compensation between the LR14 and ALC. Typical (short to medium throw) applications for the LR14 include as compact main system for theatre and A/V applications. It is available in 90° and 120° configuration.
The system includes dedicated filtering, but system equalizing is done remotely (electronically) fully utilizing the individual speaker components’ power capacity. This results in increased headroom SPL.
In applications where extended bass response is required, the LR14 can be combined with a pressure-bass (LR14B) or deep-sub system (B-series), or both.
For full system performance, the LR14 needs to be driven by an ALC amplified loudspeaker controller. Driven by the ALC, the LR14 delivers maximum sound quality with inaudible (power and excursion) protection.
LR14B
Product description
The LR14Bass is a double-tuned band-pass bass system, for both permanent and portable applications. Featuring double 12” long excursion woofers with Neodymium magnet structures, the LR14Bass delivers high quality, high output bass response from a very compact and weight efficient package. The special band-pass configuration offers LR14- matched bass response in full-space (flown) and increased efficiency in half-space (stacked) applications. The easy and accurate flying system, makes the system quick to set-up in combination with the LR14 line-array module.
The SIS pre-wiring ensures complete cable/connector compensation between the LR14Bass and ALC. The LR14Bass is designed as
high-efficient bass extension of the LR14, used in multiples depending on the array-length and low frequency requirements.
The LR14B features an integrated top hat, enabling a stand-mounted “top/sub” combination together with 3 units LR14 on the BRK-3LR14 bracket (option).
For full system performance, we recommend using the LR14Bass in combination with an ALC amplified loudspeaker controller. Driven by the ALC, the LR14Bass delivers maximum sound quality and output power with dedicated and inaudible (power and excursion!) protection.
LR18/90
Product description
The LR18/90 is a 3-way, “compact-mid-size” format line-source sound system, combining the highest sound quality possible with very high SPL capabilities and throw.
By implementing Alcons’ pro-ribbon technology for mid and high frequencies, a super-fast impulse response with up-to-90% less distortion is achieved. This enables the LR18/90 to offer a fully intuitive linear response, with perfect intelligibility and non-compressed identical tonal balance at any SPL.
The all-natural cylindrical wavefront of the multiple-patented, purpose-designed RBN702rs 7” pro-ribbon transducer and the acoustically and electronically symmetrical component configuration bring a unique pattern control in both the vertical as well as the horizontal plane, without any distortion-inducing horn constructions.
The patented 90-degree horizontal dispersion is maintained up to the highest frequencies.
The pro-ribbon’s power handling of 1500W and RMS-to-peak ratio of 1:15, caters for a superb intelligibility and throw with maximum dynamic headroom reserve.
The MF-section features a high-efficiency 6.5” midrange transducer with Neodymium motor-structure, coaxially mounted behind the HF driver in a horn-loaded configuration.
The LF section consist of 2 extended-excursion, reflex-loaded 8” woofers with oversized 3” voice-coil Neodymium motor-structure, surpassing the output of even larger drivers, while maintaining an unobtrusive face print.
The LR18/90 is driven by the Sentinel amplified loudspeaker controller, optimising the system’s response by LR18-specific drive processing and feedback for each array configuration, including presets for phase-matched low-frequency extensions.
The Signal Integrity Sensing™ pre-wiring ensures dynamic cable/connector compensation between the LR18/90 and ALC; This offers a 1:1, undistorted natural sound reproduction, regardless of cable length and amplifier impedance load (system damping factor 10.000).
The rigging system enables angle-setting on the cabinets without lifting the array, resulting in safer and faster set-up with minimal handling and a WLL of 24 cabinets under 10:1 safety.
Array configurations can be simulated in the Alcons Ribbon Calculator (ARC), Alcons’ high-resolution 3D simulation program.
LR18/120
Product description
The LR18/120 is a 3-way, “compact-mid-size” format line-source sound system, combining the highest sound quality possible with very high SPL capabilities and throw.
By implementing Alcons’ pro-ribbon technology for mid and high frequencies, a super-fast impulse response with up-to-90% less distortion is achieved. This enables the LR18 to offer a fully intuitive linear response, with perfect intelligibility and non-compressed identical tonal balance at any SPL.
The all-natural cylindrical wavefront of the multiple-patented, purpose-designed RBN702rs 7” pro-ribbon transducer and the acoustically and electronically symmetrical component configuration bring a unique pattern control in both the vertical as well as the horizontal plane, without any distortion-inducing horn constructions.
The patented constant 120-degree horizontal dispersion is maintained up to the highest frequencies.
The pro-ribbon’s power handling of 1500W and RMS-to-peak ratio of 1:15, caters for a superb intelligibility and throw with maximum dynamic headroom reserve.
The MF-section features a high-efficiency 6.5” midrange transducer with Neodymium motor-
tructure, coaxially mounted behind the HF driver in a horn-loaded configuration.
The LF section consist of 2 extended-excursion, reflex-loaded 8” woofers with oversized 3” voice-coil Neodymium motor-structure, surpassing the output of even larger drivers, while maintaining an unobtrusive face print.
The LR18/120 is driven by the Sentinel amplified loudspeaker controller, optimising the system’s response by LR18-specific drive processing and feedback for each array configuration, including presets for phase-matched low-frequency extensions.
The Signal Integrity Sensing™ pre-wiring ensures dynamic cable/connector compensation between the LR18 and ALC; This offers a 1:1, undistorted natural sound reproduction, regardless of cable length and amplifier impedance load (system damping factor 10.000).
The rigging system enables angle-setting on the cabinets without lifting the array, resulting in safer and faster set-up with minimal handling and a WLL of 24 cabinets under 10:1 safety.
Array configurations can be simulated in the Alcons Ribbon Calculator (ARC), Alcons’ high-resolution 3D simulation program.
LB18
Product description
The LB18 is a low-frequency line-array module for medium to large sound reinforcement applications; It is designed as LF array extension of the LR18 pro-ribbon line-array.
In combination with LR18, high output arrays can be formed for high-end sound reinforcement, where precise projection and long-throw is required down to the lower frequencies.
Adding LB18 modules enlarges the array length, extending the controlled (cylindrical) projection of the LR18 down to the lower frequencies, while increasing throw of the low-mid frequencies over distance.
The LB18 consist of 2 long-excursion 8” woofers in a centrally-vented configuration. The 8” woofer features a large, oversized 3” voice-coil Neodymium motor structure and dual-spider suspension with forced-venting, surpassing the output of even larger sized drivers, while maintaining an unobtrusive face print.
For full system performance, the LB18 is driven and controlled by the ALC amplified loudspeaker controller; Driven by the ALC, the LB18 delivers maximum sound quality and output power with
long-term operation reliability. The integrated factory presets in the drive processor of the ALC offer gain, phase and filtering matching, as well as array-length correction in combination with the LR18 system.
The Signal Integrity Sensing™ pre-wiring ensures dynamic cable/connector compensation between the LB18 and ALC, significantly increasing response accuracy of the low frequencies. This offers a 1:1, undistorted natural sound reproduction, regardless of cable length and amplifier impedance load (system damping factor of 10.000).
The rigging system is fully compatible with that of the LR18; The rigging system enables angle-setting on the cabinets, without lifting the array, resulting in safer and faster set-up with minimal handling. It has a WLL of 32 cabinets under 10:1 safety (or weight-equivalent in combination with LR18).
The LB18 is part of “The Ribbon Network” inventory and comes with a 6-years “no hassle” warranty.
Array configurations can be simulated in the Alcons Ribbon Calculator (ARC), Alcons’ high-resolution 3D simulation program.
LR18B
Product description
The LR18B is the dedicated low-frequency extension to the LR18 pro-ribbon line-array. It can also be combined with any other Alcons pro-ribbon system, in both permanent and portable applications.
The front-loaded system delivers a super accurate bass and sub response with highest output under lowest distortion, due to the super long-stroke 18” woofer. This new-generation transducer is fitted with a large, dual- 4.5” voice-coil Neodymium motor, enabling a significantly-extended excursion*, while maintaining a high sensitivity. Specific attention in this design has been paid to obtain lowest possible distortion. The Max-Vent™ port design combines further increased output with low power compression. *(not included in SPLpeak spec).
Optimal deployment flexibility is guaranteed: The LR18B can be used as single subwoofer or in multiples; As end-fire or cardioid array; Together with LR18 or in separate sub-only arrays. All functionality is possible in stacked or flown configurations.
The integrated stand mount adapter provides for easy top/sub combinations with any Alcons pro-ribbon system.
Rated for a high WorkingLoadLimit with 10:1 safety ratio, the versatile rigging system, with front and rear splaying possibility, enables straight or pre-curved flown (cardioid) arrays, to be flown besides or behind an LR18 array.
Array configurations can be simulated through the LR18 GLL in the Alcons Ribbon Calculator (ARC), Alcons’ high-resolution 3D simulation program.
Mobile (cardioid) stacks of up to 3 units can be transported through the PRRGLR18B pre-rig, including stack-specific softcover.
For full system performance, the LR18B is to be driven and controlled by the ALC amplified loudspeaker controller; Driven by the ALC, the LR18B delivers full operation flexibility, maximum sound quality and output power with long-term operation reliability.
The Signal Integrity Sensing™ pre-wiring ensures complete cable/connector compensation between the LR18B and ALC, significantly increasing response accuracy and reducing both linear and non-linear distortion to an absolute minimum, regardless of cable length and system impedance.
LR24/90
Product description
The LR24/90 is a 3-way, “mid-size” format line-source sound system; Loaded with Alcons’ multiple-patented pro-ribbon technology for mid and high frequencies, the system features a super-fast impulse response with up-to-90% less distortion. This results in a fully intuitive linear response, with perfect intelligibility and non-compressed identical tonal balance at any SPL.
The all-natural cylindrical wavefront of the purpose-designed RBN1202rs 12” pro-ribbon transducer and the acoustically and electronically symmetrical component configuration bring a unique pattern control in both the vertical as well as the horizontal plane, up to the highest frequencies without any distortion-inducing horn constructions. The ultra-coherent vertical dispersion enables a perfect inter-cabinet coupling for ultimate HF throw and wind-stability.
The remarkable intelligibility and maximum dynamic headroom reserve is due to the RBN1202’s enormous power handling of 2500W and RMS-to-peak ratio of 1:15, from 1 kHz to 20 kHz.
The MF-section features two high-efficiency 6.5” midrange transducers with Neodymium motor-structure, coaxially mounted behind the HF driver in a horn-loaded configuration.
The LF-section delivers a super accurate bass with highest output under lowest distortion possible. The new-generation 12” transducers are fitted with a large, dual-3.5” voice-coil Neodymium motor, enabling a significantly-extended excursion, while maintaining a high sensitivity.
The LR24/90 is driven by the Sentinel amplified loudspeaker controller, optimising the system’s response by system-specific drive processing and feedback for each array configuration, including presets for phase-matched low-frequency extensions.
The Signal Integrity Sensing™ pre-wiring ensures dynamic cable/connector compensation between the LR24 and ALC; This offers a 1:1, undistorted natural sound reproduction, regardless of cable length and amplifier impedance load (system damping factor 10.000).
The rigging system enables angle-setting on the cabinets without lifting the array, resulting in safer and faster set-up with minimal handling. The unique, patent-pending flying system facilitates both compressed and non-compressed suspension. It has a WLL of 24 cabinets under 10:1 safety.
LR28/80
Product description
The LR28 is a 3-way, “larger-format” line-source sound system, to be used as vertical array, in medium to large applications.
The LR28 combines the highest sound quality possible with very high SPL capabilities and throw. It offers a fully predictable linear response behavior, with perfect intelligibility and identical tonal balance at any SPL. By implementing Alcons’ pro-ribbon technology for mid and high frequencies, a super-fast impulse response with up-to-90% less distortion under lowest power-compression is achieved.
The all-natural cylindrical wavefront of the multiple-patented, purpose-designed RBN1402rsr pro-ribbon transducer enables a precise pattern control, without any distortion-inducing horn constructions. The 80-degree horizontal dispersion is maintained down to 190Hz.; The HF peak power handling of 3000W and RMS-to-peak ratio of 1:15, caters for a superb intelligibility and throw with maximum dynamic headroom reserve.
The MF-section features 4 high-efficiency 6.5” midrange transducers with Neodymium motor-structure in a slot-loaded configuration.
The mid section and RBN high section are jointly
mounted in/on the aluminium cassette for optimized heat-dissipation/reduced power-compression and prolonged system output.
The LF section consist of 2 reflex-loaded, custom 14” woofers with reinforced cone and large voice-coil Neodymium motor-structure for improved heat dissipation to reduce power compression.
The LR28 is powered and controlled by 4 channels of the Sentinel10 amplified loudspeaker controller; Through the integrated processing and feedback, the ALC offers LR28-specific drive processing with array-compensation, filter-presets, system eq, phase-matching, a.o.
The Signal Integrity Sensing™ pre-wiring of the LF and MF sections ensures dynamic cable/connector compensation between the LR28 and Sentinel, resulting in a fast and tight mid and bass response, while reducing distortion even further (system damping factor 10.000).
The rigging system enables angle-setting on the cabinets, without lifting the array, resulting in safer and faster set-up with minimal handling. The flying system supports different ways of array assembling and has a WLL of 24 cabinets under 10:1 safety.
Dimensional drawing
Technical specifications
| Frequency response | 74 Hz – 20.000 Hz (+/- 3 dB) |
| 53 Hz – (+/- 10 dB) | |
| Sensitivity nominal | 102 dB (200 Hz – 10 kHz) |
| Nominal impedance | 16 ohms |
| Recommended drive | Sentinel3 min., max. 6 pcs. per channel (2.7 ohms) |
| Nominal SPL peak | 126 dB (Sentinel3 200 Hz – 10 kHz) 131 dB (Sentinel10 200 Hz – 10 kHz) |
| Dispersion H x V (array) | 90° x depending on array length |
| Dispersion H x V (single) | 90° x 15° (line-source) |
Physical specifications
| System | 2-way, full-range |
| Filtering | passive |
| Driver LF | 1x AND6.5/16 6.5” Neodymium, vented |
| Driver HF | 1x RBN401 4” pro-ribbon driver |
| Connectors | 2x Speakon NL4 input/link |
| Physical dimensions | mm inches |
| Height | 173 / 108 6.9 / 4.3 |
| Width | 359 14.1 |
| Depth | 273 10.7 |
| Weight (approx.) | 8 kg 17.6 lb |
| Warranty | 6 years limited |
Albiral is dedicated to the design and manufacture of flat screen display solutions covering a wide range of professional applications including broadcast, digital signage, control rooms, corporate and CCTV. The vast majority of Albiral products sold are motorised, retractable and stationary monitors for corporate AV applications.
Arthur Holm is the leading European brand of state of the art motorised, retractable and stationary monitors whose designs are based on high end quality materials and cutting edge technology. Arthur Holm’s product range is 100% customisable and comprises retractable monitors, foldable, unfoldable, rotatable, single and double face, design wall-integration screens, multimedia kiosks and information totems.
With an extensive engineering team, AUDAC designs, engineers and manufacturers market leading audio solutions. With a solid history of innovation including the worlds first steerable column array and the worlds first web based multimedia matrix. AUDAC offers a range of installed sound products that embrace technology and innovation that meet and exceed the demands of system integrators.
Audinate is the leading provider of professional digital audio networking technologies globally. Their Dante AVIO adaptors let you use all your legacy audio gear with any Dante-connected system.
At their base in New Jersey, USA, Aurora Multimedia manufacture the most advanced AV distribution systems utilising IPBaseT™ and HDBaseT™ technologies. Their innovative control systems incorporate non-proprietary ReAX technology use web standards to break the tyranny of traditional control system vendors.
Caymon manufactures a vast range of products for portable and installed applications, ranging from equipment and touring racks, microphone, music and speaker stands to brackets, flight cases, adaptors, soft bags and accessories.
Furman is the go-to name in AC power management for professional musicians, sound engineers, broadcasters, and system integrators around the world. Furman products have saved billions of pounds worth of equipment from power problems, with the added advantage of maximising system performance.
Craftsmanship, Made in Italy and constant innovation: the conception of acoustic design by Garvan Acoustic. Garvan specialise in high end loudspeakers for marine, residential and commercial premises. Under the Garvan Acoustic Wellness brand, the company produces some of the most stylish accoustic treatment products that are installed in prestigious locations worldwide.
Established in 1984 Hall Technologies (formerly Hall Research) has been a leader in the design and manufacture of innovative Video over CATx, Matrix Switchers, Scalers, and Automation products. As the creators of the Mini-Cat®, the device that revolutionized Video over Cat5, Hall Technologies has risen to prominence in the Audio/Video industry.
MIPRO Electronics Co. Ltd, established in 1995, is a Taiwan based company that specialises in designing and manufacturing wireless microphones, portable wireless public address and other wireless audio equipment for professional and commercial applications.
Opus Technologies single and double output induction loop amplifier offer a wide range for all installations demanding optimal listening quality. Class D offers a very high efficient and compact amplifiers which combines quality, reliability and ease to use as well as clear and precise sound.
Outline is an Italian manufacturer of high-end loudspeaker systems and electronics for the live / touring and installation industry. Outline remains at the forefront of the acoustical and physical research that allows continual evolution and development of its product offering.
Pan Acoustics is an German manufacture of loudspeaker solutions designed for challenging and difficult acoustic environments. With a focus on 2D and 3D beam steering solutions, including the patented PowerLine solution allowing power, data, and audio signals to be transmitted over a standard 2 core conductor.
PANCONNECT manufacture stylish AV and power connectivity products. High quality stainless steel connection boxes, cubbies and retractors are finished to a standard you normally only find on luxury motor cars. Designed to be integrated in to furniture in meeting rooms, hotels and offices. All manufactured in the Czech Republic.
Powersoft designs and manufactures high-end and patented technologies for the professional audio industry. Powersoft state-of-the-art amplifiers can be found in an array of applications, ranging from stadiums, sporting arenas, theme parks, performance venues and airports to convention centres, churches, cinemas and clubs, and are used by the world’s leading tour sound companies.
Pragma Innovations are a developer of user-oriented operating and control devices in the audio and visual sector. With the primary objective of developing simplicity at all levels – Operation & Installation. Pragma Innovations have close collaborations with their distributors and AV system designers to ensure they deliver optimal performance at all levels.
Founded in 1977 by a group of enthusiastic audiophiles, ProCab has grown to become a key player in the AV cable industry. Today ProCab manufactures over 4000 premium quality cable and connector products meeting all the requirements of the installation, AV, live, and MI / retail markets.
Sound Control Technologies is the industry leader for camera integration solutions and has provided successful conference and video reinforcement integrations for thousands of customers worldwide. The SCT RemoteCam™ and RemoteTableKit™ systems give you freedom to place your VC camera wherever you need it in a room. Systems are available for all major codec brands including Cisco, Poly, Lifesize and ClearOne.
Stewart Audio Inc. more than a manufacturer of compact and sub-compact power amplifiers for professional applications. The ever expanding product offering includes an extensive range of Dante™ enabled products, as well as PoE, multi-channel and DSP enabled products.
With a singular focus on installed systems DSP, Symetrix delivers high performance audio hardware and software. The extensive product offering ranges from simple single unit installations to state-of-the-art high channel count Dante™ networked systems, and everything in between.
The touchONE reservation system is a complete multilingual room & workplace reservation solution for company workplaces, boardrooms, conference rooms, lecture rooms, auditoriums, classrooms, universities, hotels, sports centres and other meeting places as well as large corporate installations.
Televic conference is a manufacturer of conference systems and a offers a full range of conference solutions for applications ranging from basic discussion to full function set-ups, including simultaneous interpretation, language distribution, voting and room coupling.
